All Products

The Redarc range of electric trailer brake controllers provide an easy to operate method of controlling electric brakes on a trailer, camper-trailer, boat trailer or caravan.

he REDARC BCDC1220 is a 12 Volt 20 Amp In-vehicle DC to DC battery charger designed to keep your battery charged whilst driving. Featuring multi stage battery charging, the system charges your auxiliary battery from your vehicle to a proven 100%.

The BCDC charger will work from a wide operating range (9 – 32V) giving the option of charging from both 12V and 24V vehicle systems.

By providing a unique charging profile to each specific battery type, the smart charger is able to achieve and maintain 100% charge for your auxiliary battery. You can charge your auxiliary battery no matter what your battery is.

Proven and Tested

Compact in size, easy to install and fully sealed - water, dust and vibration are no match for the in-vehicle DC DC charger. It can handle the roughest tracks in outback Australia and even deep water crossings at Cape York. The BCDC DC to DC battery charger is suitable for installation in harsh environments or marine applications.

With an ever increasing number of electrical accessories and devices being used when travelling around Australia, along with more complex vehicle electrical systems than seen in years gone by, having the right DC battery charger has never been more important.

Designed, built and tested in Australia for our unique conditions, the BCDC in-vehicle DC to DC charger won’t let you down.

The BCDC1240-LV is a 12 Volt 40 Amp In-vehicle DC Charger featuring technology designed to charge all major lead acid batteries to a proven 100%. It’s suitable for vehicles fitted with an ECU-controlled variable voltage alternator.

The BCDC1240-LV dual battery charger features a lower voltage setting so it can operate with variable voltage alternators.

As a guide the BCDC1240-LV is suitable for battery bank sizes over 200AH. For smaller batteries of 75-200AH REDARC recommends the BCDC1225-LV.

With a wide operating range (9V – 32V), the DC to DC charger will charge from both 12V and 24V vehicle systems.

The BCDC DC to DC charger also features a Maximum Power Point Tracking (MPPT) solar regulator, extracting the maximum amount of power from solar panels to charge an auxiliary battery, even during low light conditions, when you’re parked.

With multiple levels of fault protection. The DC to DC battery charger will act as a dual battery isolator, should the voltage get too low, the start battery will be protected.

Proven and Tested

Compact in size, easy to install and fully sealed - water, dust and vibration are no match for the in-vehicle DC DC charger. Handling the roughest tracks in outback Australia and even deep water crossings at Cape York, the In-vehicle battery charger won’t let you down. The BCDC DC to DC battery charger is suitable for installation in harsh environments or marine applications.

With an ever increasing number of electrical accessories and devices being used when travelling around Australia, along with more complex vehicle electrical systems than seen in years gone by, having the right battery charging solution has never been more important.

Designed, built and tested in Australia for our unique conditions, the REDARC DC to DC charger is the brand you can trust.

Designed specifically for Lighting and produce 12V RMS output from 24VDC

Rocker Switch On/Off - Red

On/Off rocker switch
Single pole / Single throw
Blade terminals
Mounting hole diameter: 20mm
Voltage range: 12VDC
Amperage: 16A
Colour: Red LED illumination

2 Pack of gold plated 0 gauge ring terminals with colour coded silicon rubber insulators
Colour : 1 x Black and 1 x red
Ring outer diameter: 22mm
Ring inner diameter: 8.25mm
Cable entry: 12mm
Length of terminal: 49mm
Pack size: 2 Pieces
Packaging: Sliding blister and card with hang hole

Gold plated 4 gauge ring terminal with colour coded silicon rubber insulators

Colour: Black
Ring outer diameter: 16mm
Ring inner diameter: 8.3mm
Cable entry: 8mm
Length of terminal: 33mm
Pack size: 10 Pieces
Packaging: Sliding blister and card with hang hole

Gold plated 4 gauge ring terminal with colour coded silicon rubber insulators

Colour: Red
Ring outer diameter: 16mm
Ring inner diameter: 8.3mm
Cable entry: 8mm
Length of terminal: 33mm
Pack size: 10 Pieces
Packaging: Sliding blister and card with hang hole

Gold plated 8 gauge ring terminal with colour coded silicon rubber insulators

Colour: Red
Ring outer diameter: 14mm
Ring inner diameter: 8.2mm
Cable entry: 5.5mm
Length of terminal: 27mm
Pack size: 10 Pieces

Gold plated 4 gauge female fork terminal with colour coded silicon rubber insulators

Colour: Black
Fork outer width: 8mm
Fork inner width: 5.4mm
Cable entry: 8mm
Length of terminal: 23mm
Pack size: 10 Pieces

Gold plated 8 gauge fork terminal with colour coded silicon rubber insulators

Colour: Black
Fork outer width: 8mm
Fork inner width: 3.8mm
Cable entry: 4.8mm
Length of terminal: 21mm
Pack size: 10 Pieces

Gold plated 8 gauge fork terminal with colour coded silicon rubber insulators

Colour: Red
Fork outer width: 8mm
Fork inner width: 3.8mm
Cable entry: 4.8mm
Length of terminal: 21mm
Pack size: 10 Pieces

Gold plated 12 gauge fork terminal with colour coded silicon rubber insulators

Colour: Black
Fork outer width: 6.8mm
Fork inner width: 4mm
Cable entry: 2.3mm
Length of terminal: 16mm
Pack size: 10 Pieces

Gold plated 12 gauge fork terminal with colour coded silicon rubber insulators

Colour: Red
Fork outer width: 6.8mm
Fork inner width: 4mm
Cable entry: 2.3mm
Length of terminal: 16mm
Pack size: 10 Pieces

Gold plated 12 gauge female spade terminal with colour coded silicon rubber insulators.

Colour : Black
Spade Outer Width: 4.8mm
Cable Entry: 3.7mm
Length Of Terminal: 14mm

Ni plated T style Distribution Block

Accepts: 1 x 0 or 2 gauge power cable input
Outputs: 2 x 4 or 8 gauge power cable
Supplied With: 3 x Ni plated adaptor rings to adapt from 0 gauge to 2 gauge and 4 gauge to 8 gauge
Gold allen key screw fittings clear ABS perpex base and cover
Pack size: 1 Piece

Ni plated clear inline AGU fuse holder
Suits 4 or 8 gauge cable with gold allen key screw fittings and 50 amp fuse
Red rubber insert on both ends
State of the art plating process ensures maximum current transfer with minimal loss
Pack size: 1 Piece

Ni plated clear inline AGU fuse holder
Suits 4 or 8 gauge cable with gold allen key screw fittings and 50 amp fuse
Red rubber insert on both ends
State of the art plating process ensures maximum current transfer with minimal loss
Pack size: 1 Piece

Ni plated (+) positive battery clamp with gold allen key screw fittings
Accepts 2 x 8 gauge cables and 1 x multitap fitting accepting 4 or 8 gauge cable
State of the art plating process ensures maximum current transfer with minimal loss
Pack size: 1 Piece

Ni plated (-) negative battery clamp with gold allen key screw fittings
Accepts 2 x 8 gauge cables and 1 x multitap fitting accepting 4 or 8 gauge cable
State of the art ni plating process ensures maximum current transfer with minimal loss
Pack size: 1 Piece

Ni plated T style power distribution block
Accepts 1 x 4 Or 8 gauge 60 input to 2 x 4 or 8 gauge 60 outputs
Supplied with 3 x Ni plated adaptor 130 to adapt from 4 gauge to 8 gauge gold allen key screw fittings clear ABS plastic base and clear perspex cover
State of the art plating process ensures maximum current transfer with minimal loss
Pack size: 1 Piece

Stereo ground loop isolator
Eliminates hum noise through electrical systems by breaking the earth connection between the 2 connected devices
2 x female RCA input to 2 x male RCA output
Max input: 30 watts per channel
Frequency response: 20Hz to 26KHz
Size: 65mm long x 35mm diameter
Pack size: 1 Piece

2 Channel adjustable high to low level converter.

Converts speaker level audio signal to line level signal (RCA)
30 watts per channel (2 channel)
0 ~ 80db adjustable attenuation through 2 adjustable pot controls
Uses transformer technology
Housed in plastic case with mounting holes for secure mounting
Product size: 90 x 65 x 25mm

2 Channel High To Low Level Converter & Line Driver

The AAL102 is designed to convert your existing vehicles factory head-units high level (speaker output) into a line level (RCA) output allowing you to add an aftermarket amplifier, speakers or subwoofer.

Designed to be used as a high end alternative to the basic transformer type converters , this converter is designed to offer superior sonic performance to a standard converter while also offering a higher RCA voltage output (up to 10V). With less distortion and hiss (better signal to noise ratio), this converter can also be used as a line driver to boost RCA voltage from 4 volts to 10 volts, either from a head unit or even directly from an iPhone, phone or MP3 player.

Ni plated 4 gauge battery lug with gold allen key screw fittings
State of the art plating process ensures maximum current transfer with minimal loss.
Pack size: 2 Pack

Ni plated 8 gauge battery lug with gold allen key screw fittings
State of the art plating process ensures maximum current transfer with minimal loss
Pack size: 2 Pack

DETAILS

Male RCA to male RCA audio adaptors gold plated with black and red colour coded markers.
Pack size: 2 Pack

2 Female RCA sockets to 2 female RCA socket audio adaptor
Plastic body
Pack size: 1 Pack

1 Male RCA plug to 2 female RCA socket audio adaptor
Plastic body
Pack size: 1 Pack

1 Female RCA socket to 2 female RCA socket audio adaptor
Plastic body
Pack size: 1 Pack

3 Female RCA socket to 3 female RCA socket audio / video adaptor
Plastic body
Pack size: 1 Pack

Inline 3.5mm stereo socket to 3.5mm stereo socket audio adaptor
Plastic body
Pack size: 1 Pack

Standard male RCA plug to RCA socket with a second socket at right angles audio adaptor gold plated with black & red colour coded markers

Pack size: 2 Pack

Low profile male RCA plug to RCA socket with a second socket at right angles audio adaptor gold plated with black & red colour coded markers

Pack size: 2 Pack